MIMAKI JV5-130S Especificações Página 81
- Página / 292
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
3-11
Setting the media on the printer
6 Insert the unrolled part of the roll media between the platen and the pinch rollers and
pull the unrolled part until its leading edge is positioned on the front of the printer.
7 Push down the clamp lever at the rear of the printer.
The clamp lever in the front is lowered to hold the media (for temporary setting).
8 Open the front cover and pull up the clamp lever in the front of the printer.
Pinch roller
Platen
Clamp lever
- OPERATION MANUAL 1
- Foreword 2
- DISCLAIMER OF WARRANTY 3
- Requests 3
- About media 4
- FCC Statement (USA) 4
- TABLE OF CONTENTS 7
- CHAPTER 3 Printing 8
- CHAPTER 4 Daily Care 9
- CHAPTER 5 In Case of Trouble 10
- CHAPTER 1 13
- Safety Precautions 13
- Checking the accessories 14
- Dry fan unit Box 15
- Features 16
- (See 1-8) 19
- Notes on Installation 20
- Notes on Location 21
- Moving the printer 22
- Connecting Power Supply 23
- WARNING 24
- Precautions in Use 25
- CAUTION 25
- CAUTIONS and NOTES 26
- Warning for Use 27
- CAUTIONS and NOTES 27
- Recommended types of media 28
- Warning labels 29
- Basic specifications 30
- Specifications for ink 32
- Notes on USB 2.0 Interface 34
- 1 Safety Precautions 36
- CHAPTER 2 37
- Before Use 37
- Configurations and Functions 38
- 2 Before Use 40
- 2 Press the [ENTER] key once 41
- L Cyan or Blue 43
- BL Light Cyan or Light Blue 43
- Cartridge control 44
- Carriage 46
- Capping station 46
- Cutter blade and cutting line 47
- Media sensor 47
- Pinch roller 48
- Feed roller 48
- Clamp lever 48
- Post-heater 49
- Print heater 49
- Pre-heater 49
- Operation Panel 50
- How to read the display 51
- Job processing status 52
- Message indicating status 52
- How to use the keys 54
- Functions of the JOG keys 55
- Modes and Menu Screens 56
- About Function Menus 57
- 2 Press the [FUNCTION] key 58
- Outline of menu hierarchy 60
- Direct keys 62
- SET UP functions 63
- MAINTENANCE functions 65
- MACHINE SET functions 68
- NCU functions 70
- CHAPTER 3 71
- Printing 71
- Operation flow 72
- Turning the power on 73
- Power Switches 74
- Adjusting the head gap 75
- 3 Press the [END] key 76
- 2 Select a angle as setting 78
- 3 Retighten the knobs 78
- Roll holder securing screw 79
- Media support bar 80
- Rightmost pinch roller 83
- Suction hole 83
- Media press 83
- Media end 83
- Input of MediaLength 86
- MEDIA LENGTH = 50 m 86
- Setting the torque limiter 87
- 4 Push down the clamp lever 89
- How to select a user type 90
- How to check the user type 90
- Operating the heaters 91
- 2 Press the [HEATER] key 92
- Example of beading 93
- In case of heater trouble 95
- [PG DROP ADJUST.] 96
- Abnormal pattern 98
- Normal pattern 98
- 2 Press the [CLEANING] key 99
- 5 Press the [ENTER] key 100
- 4 Press the [ENTER] key 102
- CORRECTION PATTERN 103
- Correction value is too small 104
- Correction value: 104
- -255 ~ 255 104
- Correction value is too large 104
- OverlapClearance 104
- 6 Press the [ENTER] key 106
- Effective Plotting Area 107
- Establishing the Origin 108
- Printing an image 109
- 3 Press the [ENTER] key 111
- 2 Press the [] key 112
- Automatic cleaning 113
- 4 Press the [FUNCTION] key 114
- When setting to CLEANING 115
- When setting to WIPING 117
- [INK NEAR END] 118
- [INK END] 118
- [INK END][INK NEAR END] 119
- 2 Press the [ENTER] key 120
- 3 Printing 122
- EXPIRED INK IN USE 124
- NOT RECOMMENDED !! 124
- PRESS [ENT] 124
- 8 to 10 125
- 2 Press the [REMOTE] key 126
- Turning the power off 127
- CHAPTER 4 129
- Daily Care 129
- Routine Maintenance 130
- Notes on cleaning solution 131
- Cleaning exterior surfaces 131
- Cleaning the platen 131
- Cleaning the media sensor 132
- Cleaning the media press 132
- Opening the maintenance cover 133
- L. ∗ > [JV5-01] 135
- ST.MAINTENANCE 135
- CARRIAGE OUT <ent> 135
- COMPLETED :end 137
- ∗Being Initialized∗ 137
- PLEASE WAIT 137
- 7 Press the [ENTER] key 140
- 12Press the [ENTER] key 141
- 11Press the [ENTER] key 147
- To step 5 To step 11 148
- PUMP tube cleaning 151
- 4 Daily Maintenance 152
- Wiper cleaning 153
- [CR.MAINTENANCE] 156
- Clean the head media sensor 157
- 9 Press the [ENTER] key 158
- Input range: OFF, 1 to 168 160
- [ROUTINE SETUP] 162
- Other maintenance functions 169
- [BOX EXCHANGE LV] 171
- L .1 > [ JV5-01 ] 172
- ! WasteTANK FULL/NONE 172
- ! NearFULL WASTE TANK 172
- Cleaning of Flushing Box 174
- 3 Open the pump cover T 175
- When this figure reaches 176
- 100%, the warning or error 176
- Replacing F-Box filters 177
- F-BOX filter 178
- F-BOX filter base 178
- 1 Press [] key 179
- [FILTER EXC. LV.] 181
- 3 Open the front cover 187
- Install the new cutter unit 188
- CHAPTER 5 189
- In Case of Trouble 189
- Power does not turn on 190
- Check the basic operation 191
- If image quality is poor 192
- (jet deviation) 193
- [DISCHARGE&WASH] 194
- 4 Remove the ink cartridges 195
- 5 In Case of Trouble 198
- Ink cartridge trouble 200
- Warning messages 203
- Error messages 206
- CHAPTER 6 213
- Operation for Functions 213
- Invoking SET UP functions 214
- (See 6-31) 216
- (See 3-33) 216
- PRINT MODE 217
- INK LAYERS 219
- DRYING TIME 219
- AUTO CUT 220
- PRE-FEED 220
- COLOR PATTERN 220
- PRIORITY 221
- (See 3-43) 222
- (See 3-45) 222
- (See 3-5) 222
- MEDIA DETECT 223
- SETUP RESET 223
- List of functions 224
- 2 Press the [ST.MAINT] key 225
- [MEDIA RESIDUAL] 226
- 6 Operation for Functions 228
- Setting a MACHINE SETUP 230
- DRY & EXHAUST FAN 231
- DRYNESS FEED 232
- CONFIRM. FEED 232
- PRE-FEED METHOD 233
- HEATER SETUP 233
- MEDIA CUT 233
- TIME SET 233
- UNIT SETUP 234
- STAMP SETUP 234
- Test Draw Arrange 235
- Detection of media 235
- MACHINE NAME 235
- INFORMATION 236
- ERROR HISTORY 236
- MAINTE. HISTORY 236
- PRT.modeHISTORY 236
- Ink replacement report 237
- Serial&DealerNo 237
- Invoking NCU functions 238
- Outline of the NCU functions 239
- NG JUDGEMENT (*1) 240
- COND.INDICATION 240
- DISPLAY setting 241
- Applied settings of functions 242
- Detailed settings of heaters 243
- Input range: 244
- PRE [OFF, 20 - 60] ° C 244
- PRT [OFF, 20 - 60] ° C 244
- POST [OFF, 20 - 70] ° C 244
- How to operate function menus 245
- Change is 247
- Functions related to ink 248
- Function Flowchart [BOOT] 250
- DECIDE = [ENTER] 262
- TIMER SET = [FUNC.] 262
- CLtypeSetWithFUNCkey 267
- :FORE&BACK 280
- 10 to 1000 280
- D201515-21-31102014 290
- Printed in Japan 292
Manuais e produtos relacionados com Digitalizar e Imprimir MIMAKI JV5-130S
Digitalizar e Imprimir MIMAKI JV5-320S Especificações
(130 páginas)
(130 páginas)
Digitalizar e Imprimir MIMAKI JV33-160 Especificações
(202 páginas)
(202 páginas)
Digitalizar e Imprimir MIMAKI JV3-75SPII Especificações
(150 páginas)
(150 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.050 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais