MIMAKI JV5-160S Especificações Página 132
- Página / 262
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
CHAPTER 4 Daily Maintenance Cleaning the nozzle [NOZZLE WASH]
4-10
Cleaning the nozzle [NOZZLE WASH]
Perform cleaning of the nozzles in the heads to prevent them being clogged with coagulated ink.
STEPS:
1 Make sure that the printer is in LOCAL mode, and then press the [ST.MAINT] key.
If it is in REMOTE mode, press the [REMOTE] key.
2 Select [NOZZLE WASH] by pressing the [] key twice and press the [ENTER] key.
The carriage will come out of the capping station.
3 Open the right maintenance cover.
Be sure to wear the supplied goggle and gloves.
The ink contains an organic solvent. If ink settles on your skin, immediately
wash it off with water. If you get ink in your eyes, immediately wash your eyes
with a lot of clean water for at least 15 minutes. In doing so, also wash the back-
side of eyelids to rinse ink away completely. Then, consult a doctor as soon as
possible.
If nozzle clogging cannot be corrected even after repeating the cleaning proce-
dure described here several times, execute the [FILL UP INK] (Refer to “If noz-
zles cannot be unclogged [FILL UP INK] (p.3-32)” ) , [DISCHARGE&WASH]
(Refer to “[DISCHARGE&WASH] (p.5-6)” ) functions. If the remedies instructed
here do not work, contact your dealer or an office of MIMAKI.
If both of the two cartridges in a set are in [INK NEAR END] or [INK END] status,
the nozzle cleaning function (ink suction) is not activated. Replace the car-
tridges that are in [INK NEAR END] or [INK END] status with ones containing a
sufficient amount of ink.
PRE PRT AFT
35°C 40°C 50°C
L. ∗ > [JV5-01]
width : ∗∗∗∗ mm
ST.MAINTENANCE
CARRIAGE OUT <ent>
Twice
ST.MAINTENANCE
NOZZLE WASH <ent>
- OPERATION MANUAL 1
- DISCLAIMER OF WARRANTY 3
- Requests 3
- FCC Statement (USA) 4
- Foreword 5
- CHAPTER 3 Print Output 10
- CHAPTER 4 Daily Maintenance 11
- CHAPTER 5 In Case of Trouble 12
- TABLE OF CONTENTS 13
- CHAPTER 1 15
- Safety Precautions 15
- Checking the accessories 16
- Front exhaust unit Box 18
- Name QTY Remarks 19
- 1 Roll screen 160 (130) 1 19
- 4 Front exhaust unit Box 1 19
- Features 20
- Pictorial signs 23
- Notes on Installation 24
- Notes on Location 25
- Moving the printer 26
- Power Supply Connection 27
- WARNING 28
- Precautions in Use 29
- CAUTION 29
- CAUTIONS and NOTES 30
- Recommended types of media 31
- Warning labels 32
- Basic specifications 33
- *2 Main unit and heater 34
- *3 Without front exhaust unit 34
- Specifications for ink 35
- Notes on USB 2.0 Interface 36
- CHAPTER 2 39
- Basic Use of Printer 39
- Names of Parts and Functions 40
- 3 Press the [ENTER] key once 44
- Cartridge control 46
- Carriage 48
- Capping station 48
- Cutter blade and cutting line 49
- Media sensor 49
- Pinch roller 50
- Feed roller 50
- Keep the pinch rollers 50
- Clamp lever 50
- After-heater 51
- Print heater 51
- Pre-heater 51
- Operation Panel 52
- How to read the display 53
- Job processing status 54
- Message indicating status 54
- BUSY lamp 55
- HEAT SW lamp 55
- How to use the keys 56
- Functions of the JOG keys 57
- Modes and Menu Screens 58
- About Function Menus 59
- 2 Press the [FUNCTION] key 60
- Outline of menu hierarchy 62
- Direct keys 64
- SET UP functions 65
- MAINTENANCE functions 67
- MACHINE SET functions 70
- NCU functions 71
- CHAPTER 3 73
- Print Output 73
- Operation flow 74
- Turning the power on 75
- Starting up the printer 76
- Adjusting the head gap 77
- 3 Press the [END] key 78
- 2 Select a angle as setting 80
- 3 Retighten the knobs 80
- Roll holder securing screw 81
- Media support bar 82
- Rightmost pinch roller 85
- Media encoder roller 85
- Media press 85
- Media end 85
- Setting the torque limiter 89
- 3 Push down the clamp lever 91
- How to select a user type 92
- How to check the user type 93
- Operating the heaters 94
- 2 Press the [HEATER] key 95
- What is beading ? 96
- Temperature adjustment 97
- In case of heater trouble 98
- [PG DROP ADJUST.] 99
- 6 Press the [ENTER] key 100
- Abnormal pattern 101
- Normal pattern 101
- 2 Press the [CLEANING] key 102
- 5 Press the [ENTER] key 103
- 4 Press the [ENTER] key 104
- 35°C 40°C 50°C 105
- L. ∗ > [JV5-01] 105
- PRE PRT AFT 105
- Correction value: 107
- -255 ~ 255 107
- Correction value is too large 107
- OverlapClearance 107
- Correction value is too small 107
- Effective Plotting Area 110
- Establishing the Origin 111
- Printing an image 112
- 2 Press the [REMOTE] key 113
- 4 The printer start printing 113
- 2 Press the [DATA CLEAR] key 114
- 3 Press the [ENTER] key 115
- Automatic cleaning 116
- 4 Press the [FUNCTION] key 117
- [INK NEAR END] 118
- [INK END] 118
- [INK END][INK NEAR END] 119
- 2 Press the [ENTER] key 120
- Turning the power off 121
- CHAPTER 4 123
- Daily Maintenance 123
- Routine Maintenance 124
- Notes on cleaning solution 125
- Cleaning exterior surfaces 125
- Cleaning the platen 125
- Cleaning the media sensor 126
- Cleaning the media press 126
- Opening a maintenance cover 127
- ST.MAINTENANCE 131
- COMPLETED :end 131
- ∗Being Initialized∗ 131
- NOT POW-OFF !! 131
- PLEASE WAIT 131
- 7 Press the [ENTER] key 134
- 11Press the [ENTER] key 134
- To step 5 To step 10 142
- PUMP tube cleaning 144
- Wiper cleaning 146
- [CR.MAINTENANCE] 149
- Never rub the nozzle part 150
- Media sensor at the heads 151
- Input range: OFF, 1 to 168 153
- Other maintenance functions 161
- FULL, or NONE 163
- 3 Open the front cover 167
- Install the new cutter unit 168
- CHAPTER 5 169
- In Case of Trouble 169
- Power does not turn on 170
- Check the basic operation 171
- If image quality is poor 172
- (jet deviation) 173
- [DISCHARGE&WASH] 174
- 4 Remove the ink cartridges 175
- Ink cartridge trouble 179
- [ERROR HISTORY] is displayed 181
- Warning messages 182
- Error messages 185
- CHAPTER 6 191
- Operation for Functions 191
- Invoking SET UP functions 193
- Set the printing conditions 194
- (See 3-34) 195
- (See 6-29) 195
- PRINT MODE 196
- INK LAYERS 198
- DRYING TIME 198
- AUTO CUT 199
- PRE-FEED 199
- COLOR PATTERN 199
- (See 3-44) 200
- (See 3-5) 201
- List of functions 202
- 2 Press the [ST.MAINT] key 203
- RESIDUAL] 204
- Setting a MACHINE SETUP 208
- DRYNESS FEED 209
- CONFIRM. FEED 209
- TIME SET 209
- DEODORIZE FAN 209
- UNIT SETUP 210
- STAMP SETUP 210
- MACHINE NAME 211
- INFORMATION 212
- ERROR HISTORY 212
- MAINTE. HISTORY 212
- PRT.modeHISTORY 212
- Serial&DealerNo 214
- Invoking NCU functions 215
- Outline of the NCU functions 216
- NG JUDGEMENT (*1) 217
- COND.INDICATION 217
- DISPLAY setting 218
- Applied settings of functions 219
- Detailed settings of heaters 220
- How to operate function menus 223
- Change is 225
- Functions related to ink 226
- Remove the cleaning 227
- Function Flowchart [BOOT] 228
- To p.6-42 230
- From p.6-40 232
- To p.6-48 236
- To p.6-50 238
- From p.6-46 238
- From p.6-48 240
- To p.6-54 242
- From p.6-52 244
- To p.6-56 244
- From p.6-54 246
- To p.6-58 To p.6-58 246
- To p.6-60 248
- From p.6-56 From p.6-56 248
- From p.6-58 250
- To p.6-64 252
- From p.6-62 254
- To p.6-68 256
- From p.6-66 258
- D201515-1.00-11082006 260
- Printed in Japan 262
Manuais e produtos relacionados com Digitalizar e Imprimir MIMAKI JV5-160S
(146 páginas)
Digitalizar e Imprimir MIMAKI TS5-1600AMF Especificações
(288 páginas)
(288 páginas)
(288 páginas)
Digitalizar e Imprimir MIMAKI UJF-3042FX Especificações
(138 páginas)
(138 páginas)
Digitalizar e Imprimir MIMAKI JF-1631 Especificações
(142 páginas)
(142 páginas)
Digitalizar e Imprimir MIMAKI UJF-3042HG Especificações
(156 páginas)
(156 páginas)
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.066 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais